Finish a Basement: A DIY remodeling adventure!
Check out this section for help a\s you begin basement construction

Return to our Home page
Visit our project planning page to learn how to prepare to finish your basement whether you're remodeling your basement by yourself, or hiring a contractor to finish your basement
Visit our design page to see how we created our basement design, and for tips on how you can design the basement of your dreams
Check here for information on the tasks you'll need to complete to finish your basement. Complete with the lessons we learned as we remodeled our basement, and tips to help you avoid some of the mistakes we made.
Whether you're designing a dedicated home theater, or creating a multi-purpose media room, check here for tips on selecting home theater components, and calibrating, and setting up your AV equipment
Check here to follow along as we complete our DIY basement remodeling project!






 

>Home >Basement construction >How to stain & finish doors

How to stain doors & how to finish doors

See the previous topic in this sectionSee the next topic in this section

How to stain & finish doors

how to stain doors & how to finish doorsWhen it comes to woodwork, nothing beats a natural finish! Though painting is quicker, if you’re willing to spend the time staining & finishing doors you’ll be rewarded with a beautiful natural finish. Here’s how!

What you’ll need

  • Doors
  • Medium (180 grit) sandpaper or sanding sponges
  • Wood conditioner (if you’re staining a softer wood such as pine- a quart is enough for 2-3 doors)
  • Stain (a quart is enough for several doors)
  • Polyurethane finish
  • Staining rags, & tack cloth
  • Shop Vac (optional)
  • Sawhorses (optional but they’ll make it much easier)
  • 3” flat brush (make sure you get one suitable for oil-based stains/paints)
  • 1 ½” or 2” brush (optional – use if staining doors with intricate detailing)
  • Mineral Spirits (for cleanup)
  • A well-lit, well-ventilated area such as a garage (DON’T stain in the house – unless you’re sleeping somewhere else)

wood conditioner, stain, & polyurethane


Conditioning wood doors

NOTE: This section applies to finishing pine doors. If using hardwood (Oak, etc.) proceed directly to How to stain a door (below).

conditioning soft wood such as pine

1. Lay the door flat on sawhorses. Lightly sand the entire door (both sides)

2. Use tack cloth and/or a shop vacuum to clean the dust from the door.

3. Stir the conditioner (never shake!) and spread it on one side of the door using a 3” brush. (Since you need to stain within two hours of conditioning, you’ll do one side of the door at a time.) Wait 15-30 minutes and wipe up any excess using a clean rag.

4. Clean your brush using Mineral Spirits (or other product for oil-based stains) and dry it with a rag.

5. Be sure to proceed to How to stain a door within two hours of conditioning the wood.

How to stain a door

NOTE: If your door has intricate detailing you may want to use a 1 1/2" or 2” angle brush for certain areas. You don’t want to leave puddles of stain in those areas.

1. Stir (never shake!) your stain and apply a thin layer (following the grain of the wood) on the entire surface of the conditioned side of the door, and the edges of the door using a 3” brush.

2. Wait 15-30 minutes and wipe away any stain that has not absorbed into the wood.

3. Clean your brush using Mineral Spirits (or other product for oil-based stains) and dry it with a rag.

4. To achieve a darker finish, repeat steps 1 & 2 following the drying time instructions on the can (usually 4-6 hours).

How to finish a door

1. Stir (never shake!) your polyurethane and apply a thin layer to the stained wood using a 3” brush. Follow the grain of the wood. If you have a door with intricate detailing, you may want to use a smaller brush instead- you don't want to leave any puddles.

2. Clean your brush using Mineral Spirits (or other product for oil-based stains) and dry it with a rag.

Sanding between coats of polyurethane

Applying polyurethane

 

3. After the first coat dries (3-4 hours) lightly sand. This will give a slightly rough finish to allow the 2nd coat of polyurethane to adhere better.

4. Apply a 2nd coat following steps 1 & 2 above.

5. Allow the door to dry thoroughly overnight before hanging.

Finished door after sanding, staining, and coating with polyurethane6-panel door installed

FAB door finishing tips

  • Don’t use polyurethane on the sides of the door. It may cause the door to stick on humid days.
  • When you spread the polyurethane, be sure to not leave any puddles on the wood. It may cause drips.
  • Wipe the sides and back edge of the door so avoid unsightly drips that will harden and make the door look sloppy.
  • Apply stain sparingly on the sides of the door and wipe the back of the door quickly with a rag to catch any drips.

 

Construction Topics

Tools you'll need

The 3-4-5 rule

How to frame a wall

How to attach walls

How to install insulation

Drywall estimating

How to hang drywall: Step-by-step

How to cut drywall

How to cut around outlets and openings

Drywall installation tips

How to frame a door

How to trim a door to fit

How to finish a door

How to frame around poles

How to finish drywall

How to sand drywall

Tips for buying, finishing, & installing baseboard molding

How to fix squeaky floors

Home |Project Planning | Design | Construction | Home Theater | Our Progress | About this site


©2008-2012 Wilk Web Works
All content is protected by copyright. Unauthorized duplication is prohibited.
All rights reserved.